BetaFPV BEC Board for Naked Camera

Sale price BND$10.00 Regular price BND$17.00

Are you still worry about naked GoPro will turn off caused by not solid power? Do you want to make your naked GoPro be super neat and light? This BEC board could help you. It integrated 5V@2A BEC, stock GoPro buttons and LED, pluggable connectors and remote recording.

The BEC Board has been upgraded to the V1.1 version. With the new version, we don’t need to use 2 shims when assembling the BEC board on the GoPro motherboard, which can solve the problem that the two interfaces may loose when locked.

We did found the issue in our BETA TEST version that it may cause the FC or GoPro mainboard to burn out when the 3-pins power cables plugged in when powering on. Special thanks to Guido Fabbrini reminding us of the risk. After lots of tests and troubleshooting, we totally had solved this issue before we released the BEC board V1.0.

So pilots who received the V1.0 version please don’t worry, V1.0 version is totally safe.

This BEC board fits for GoPro HERO6 and HERO7 Black. But NOT for HERO8.

Many thanks for Richárd Papp and those people who devoted their time and energy to the cinewhoop researching. Thanks for the FPV community to gather such awesome ideas. If you wanna know more about cinewhoop, click the link below to join us on Facebook.

>>NAKED Cinewhoop Community

Bullet Point

  • BEC Board is specially designed for Naked GoPro HERO which weighs about 1.5g, makes your naked GoPro lighter and easier to install on your drone.
  • The BEC output voltage is 5V@2A, avoid the accident of power off which is caused by the insufficient power supply for the FC board.
  • Integrated GoPro stock buttons, Power/Mode Button and Record Button
  • Integrated GoPro stock LED to know the status of the camera.
  • Pad is available for pilots to control the GoPro recording via the radio transmitter.
  • With the pluggable connector, which is easier to connect with your flight controller for power supply and recording.

    Specification

    • Item: BEC Board for Naked Camera
    • Weight: 1.48g
    • Output: 5V@2A
    • Input Voltage: 2-4S 
    • Connector: GH 1.25 3P Connector

    Diagram of BEC Board

    The two buttons on the BEC board has the same function as the stock GoPro buttons. Three actions we will use frequently.

    • Power On - Press the Power/Mode button and the LED flashes three times and light off. 
    • Start Record - Press the Record button once and LED flashes slowly. If LED flash once and light off, it means there is no SD card. 
    • Stop Record - Press the Record button and LED stop slow flashing.

    LED Status 

    Under normal operation, plug the GH1.25 connector into the naked camera firstly, then connect with the battery. The LED will flash once, then you should press the Power/Mode button once in a second to power on. The LED on the BEC board has the same status as the stock LED on the GoPro mainboard.

    Indication Button Operation LED Status
    Power On Press the Power/Mode button once Flash 3 times and light off
    Power Off Press the Power/Mode button for 5 seconds Flash 7 times and light off
    Start Record Press the record button once Continuously slow flash
    Stop Record Press the record button once Flash 3 times and light off
    Mode Switch Press the Power/Mode button once Check the mode on LCD Display

    How to Setup Remote Record

    Pilot could use the switch on radio transmitter to start/stop record. Some more configuration needed.

    For example, if you use F4 FC V2.0 in the drone, like the 95X whoop drone, the connection diagram is shown below. The yellow cable (FC B12 pin pad) is just for the remote record.

    We use the Pinio function in Betaflight to control record. First, setup the Pinio function of the B12 pin in the FC board.

    resource FLASH_CS 1 NONE
    resource PINIO 1 B12
    set pinio_box = 40,255,255,255
    save

    Next, map one of the switch channels in your radio transmitter to this Pinio (aka USER1). As shown below, we map the AUX4 channel in the radio transmitter to USER1 Pinio. The cursor in the orange zone means button released and white zone means pressed. So keep the cursor in the orange zone in default.

    Third, check if the Pinio function works. Change the switch and make the cursor move from the orange zone to the white zone, and finally back to the orange zone. Now you could check the LED status to know if the record starts. Use the same process to stop recording.

    If you use the 12A F4 AIO FCboard, like the 85X whoop drone, you will use the LED_STRIP pin (aka A08 pin pad) for the Pinio function.

    resource LED_STRIP 1 NONE
    resource PINIO 1 A08
    set pinio_box = 40,255,255,255
    save

    Know more about the Betaflight Pinio function.

    Parts of Naked Camera Series

    We know some of the pilots might have a question about how to get the case for the naked GoPro or some might wanna grab the GoPro Lite Camera directly. Here we provide some more choices for your better installation. You can also find the STL File for Naked Camera Series here.

    >>Click here to check the STL Files forNaked CameraSeries.

    How to Disassemble GoPro HERO6 Black

    Special thanks to JONAH BLAESER who provided the method of disassembling GoPro HERO6 Black. If you are interested, please check the link to know the specific steps to make your own naked GoPro. 

    GoPro HERO6 Black Disassembly Guide 

    Note: Do this at your own risk. You will lose your GoPro’s warranty and you may end up bricking the camera if something goes wrong. This guide is not authorized by GoPro and your camera is not guaranteed to work afterward. BETAFPV will not be held responsible for this action.

    Package

    • 1 * BEC Board for Naked Camera
    • 1 * H1.25 Power Cable (80mm 30AWG)